How to Hang Your Framed Art
Our frames come with two brackets to ensure the virtually sturdy hold. Unlike hanging framed pieces with wire backings, these brackets prevent the frame from shifting and hanging askew once they are secured to the wall. Unless requested, our frames do not come with whatsoever screws or other materials needed to hang the framed art. Click here to read more about our framed art.
What's in the Box?
All framed fine art pieces are shipped in a flat box. The framed piece and ii brackets are shipped with the frame. Ane bracket will be fastened to the frame using three screws and an additional subclass will exist attached lower on the frame using tape. The additional bracket that is taped to the frame is what you lot will screw into the wall. For larger framed fine art, two brackets will be attached to the back of your slice and two to hang your framed art will be taped to the dorsum.
Needed to Hang Framed Art
1. wall space
two. framed art
three. three screws
4. screw driver
5. level
6. stud finder (optional)
Step 1 - Find a spot
Notice a spot in the room to hang the art. You desire to cull an area on the wall where the piece will fit. If the piece is too big for the area in which it is placed, it will overpower the room. If the framed fine art is too small for the infinite, it will go unnoticed.
You lot can use a stud finder to find a spot in the wall that volition better support the framed piece. Stud finders are used to find the studs inside of the walls and add more support for the spiral and frame when yous drill into the wall.
Step Two - Remove the extra subclass
Carefully have off the extra bracket that is taped on the back of the frame. This is the bracket that will need to be screwed to the wall.
Stride Iii - Put the bracket against the wall
Concur it upwards against the wall in the desired spot. Make sure that the elevated part is facing up and away from the wall. The three holes should be downwards and flush against the wall.
Step Four - Arrive even
Concur up the level on top of the bracket, make sure it is flat confronting the bracket for the best results. The level should also be affluent against the wall. Move the subclass against the wall until the level shows that the bracket is even.
Step Five - Marker in the holes
Marking inside of the showtime hole of the bracket. Yous tin can use a pencil, pen or any other writing utensil (one time the screws are in, y'all will no longer be able to see the marks). Exercise the same for the 2nd and third holes on the subclass.
Step Half dozen - Line the get-go pigsty upwards
Line the starting time screw up with the showtime hole. Once you take the screw in identify in the pigsty of the bracket, you can permit go of the bracket and let it hang.
Step Vii - Fasten the screw
Using the spiral driver, spike the first screw into the wall. For best results, practice not fasten the screws all the way in until they are all in place.
Step Eight - Fasten the 2d and tertiary screws
Following steps vi and seven, secure screws in the 2d and third pigsty.
Stride Nine - Hang the framed art
The bracket that is attached to the frame should at present fit on summit of the bracket that is screwed into the wall. Once the bracket is completely secured to the wall, take the frame and hold it so the back is facing the wall. Move the frame towards the wall and place the subclass on the dorsum of the frame frame onto the subclass you secured on the wall.
Step X - Prove it off
Now your frame is hung and ready to be shown off!
All of our framed pieces come with 100% satisfaction guarantee! If yous do not like the manner your framed artwork looks or it arrives damaged, contact one of our cordial customer service representatives at 800-418-2166 or support@framedart.com. For more contact information, visit our contact u.s.a. page. Click here for a step by step tutorial on how to hang your sheet!
Post a Comment for "Shoukd Wall Art Be Hung Wit Wire or With 2 Bracket"